The following page is currently in the process of being created, is undergoing a major structural rework and/or is being moved. The reason for this is: "This engine is currently TM'd, and not actually fully in the game yet!"
Well, not to worry, for Nanotrasen's subcompany: Hayne's Power Solutions™ have your back! By ordering our newly created fission based nuclear reactor, we guarantee full power availability to your station, today!
Before we begin, it's important you understand a few key words that are going to be repeated throughout this guide:
Neutrons per generation (K): Rate of heat gain in the reactor.
Moderator: Gasses that influence the performance and power production of the reactor
Power: The ratio between the current heat and the heat required for a meltdown
How the Reactor Works
The Nuclear Reactor has two inputs: Moderator and Coolant.
The first thing we're going to worry about is the coolant loop. Our reactor is cooled through a simple process: Uranium fuel rods are placed into the reactor which immediately starts the reaction, creating constant heat. Our coolant gas is pumped into the reactor, heats up to the heat of the reactor, and then carries said heat out. The colder the gas you put into the loop, the faster the reactor cools down. Innately, it’s set up so that the temperature loss from coolant intake is balanced out against the heat generated by the fuel rods, represented by the controllable figure called K (Neutrons per generation). NOTE that the coolant gas can potentially retain heat and actually heat up the reactor, so, be certain to check the thermometers on the coolant loop often!
Second is the moderator. For our reactor to create power, it has to have a fuel gas inside it's moderator input. The normal moderator we use by default for standard nuclear reactors is a 90% oxygen and 10% plasma mix.
Important reminder!
The reactor won't produce power if it has no fuel moderator gas!
Reactor Setup 101
After ordering your nuclear reactor from cargo, don't forget to order a crate of RBMK grade nuclear fuel rods as well!
The first step is to take a moment to look at each part in the crate:
RBMK Wall
RBMK Input
RBMK Moderator Input
RBMK Output
RBMK Core
Each crate comes with 5 walls, 1 input, 1 output, 1 moderator input, 1 core and 1 control rod computer board. With these parts, you should be able to assemble your own reactor with our patented modular reactor design!
Here is an example design:
After assembly, you are able to use a multitool to confirm your reactor design by updating the core. Here is the above design after it's parts and design have been confirmed:
Once you have your reactor built, make sure to give it a proper coolant and moderator supply, and to handle the waste gases from it. After you have confirmed that, you are able to link a control rod computer to the reactor with a multitool.
After all that, you may now insert the fuel rods and adjust the control rod insertion via the control rod computer. Don't forget you can monitor the reactor's statistics with your PDA!
Gases
Fuel
Oxygen
Found in: Atmospherics Used for: Fuel
Description
Power production multiplier. Allows you to run a low plasma, high oxy mix, and still get a lot of power.
Plasma
Found in: Atmospherics Used for: Fuel
Description
Power production gas. More plasma -> more power, but it enriches your fuel and makes the reactor much, much harder to control.
Tritium
Found in: Atmospherics Used for: Fuel
Description
Extremely efficient power production gas. Will cause chernobyl if used improperly.
Permeability
BZ
Found in: Atmospherics, Cargo Used for: Permeability
Description
Increases your reactor's ability to transfer its heat to the coolant, thus letting you cool it down faster. (But your output will get hotter)
Water Vapour
Found in: Atmospherics Used for: Permeability
Description
More efficient permeability modifier.
Hyper Noblium
Found in: Atmospherics Used for: Permeability
Description
Extremely efficient permeability increase. (10x as efficient as bz)
Depletion
Nitryl
Found in: Atmospherics Used for: Depletion
Description
When you need weapons grade plutonium yesterday. Causes your fuel to deplete much, much faster. Not a huge amount of use outside of sabotage.
Fuel rods
Regular Fuel Rod
Found in: Cargo Used for: Fuel for nuclear reactors
Description
The most common type of fuel rod for RBMK grade nuclear reactors. The most safe.
Telecrystal Fuel Rod
Found in: Uplinks Used for: Telecrystal duplication
Description
Rare incidents report telecrystal fuel rods being found in our nuclear reactors, they seem to absorb some radiation to grow in side.
Bananium Fuel Rod
Found in: Clown Planet Used for: Bananium duplication
Description
The bananium fuel rod is often able to be heard honking from our reactors. Strangely, the bananium inside grows in amount as radiation is absorbed.
Maintenance
So you’ve started the reactor up, but your job isn’t done yet. ever. You’ve still got to prepare to shut the reactor down, change the rods, and make sure it doesn’t blow up halfway! The higher the K the more power and heat you produce, at 1k it should be stable, but if it’s not, adjust the decimal points.
Shutting down the reactor
Once your timer to change the rods is up, go ahead and turn the reactor rod control to 0 K, this will cause the reactions in the reactor to stop, and slowly settle down, while this is happening, you want to insert two co2 cans into the direct moderator input, and set the moderator to 1000-1500 kpa, this will ration out your 9000kpa odd co2 for shutdown. Once the reactor power is under 20 percent, you are then able to remove the fuel rods. This will shut the reactor down for good, now you want to unwrench your co2 cans, refill them and bring them back again. You are now good to insert new rods into the reactor and start it up again. NOTE: Please keep spent rods away from normal rods, remember to reset the moderator input amount.
Repairing the reactor
If your reactor gets damaged, either from the pressure or heat, you can repair it with a welding tool and sealant, this will repair the seals and make sure you don’t blow up next time you start it up.
Tips
Be careful to not exhaust your plasma supply. It is recommended you don't max out the moderator input when youre running plasma + O2, or you're at a tangible risk of running out of those gasses from atmos.
The reactor consumes moderator gasses very quickly, so keep this in mind before you use permeability gasses for riskier setups.
You don’t need to shut down the reactor to do maintenance, you only need to bring it down to 20% power.
This engine synergises well with other atmos based engines, try hooking it up to a TEG for free power.
You can cook food such as steak on the reactor's surface.
If the reactor makes banging noises, it’s not being actively cooled with coolant, and is taking damage.
Sabotage
Sabotaging the Nuclear Reactor is incredibly easy to do, but can also be incredibly easy to fix depending on how much effort you put into your handiwork. Make sure there are no competent engineers nearby, roll up your sleeves, and let's get to work. You have a choice of starting either a meltdown or a blowout, with the latter being the deadliest but easiest to fix.
Meltdown:
Flood reactor moderator line with plasma, they won't be able to mitigate the reaction with control rods.
Shut off coolant entirely. Raise control rods.
Swap all fuel out with spent fuel, as it's way stronger.
Blowout:
Shut off exit valve for quick overpressure.
Cause a pipefire in the coolant line (LETHAL).
Tack heater onto coolant line (can also cause straight meltdown)
